Printed from Kezuriba (kezuriba.net/en/fits/shaft-p6/)
p6 tolerance (shaft) — limit deviations
Upper and lower limit deviations of shaft tolerance class p6 (shafts use lower-case letters), in µm (0.001 mm). Add them to the nominal size to get the permitted size range. Example: a Ø25 p6 shaft must be between 25.022 and 25.035 mm.
▤p6 limit deviations (µm)
| Nominal size (mm) | Upper | Lower | Tolerance | Calc |
|---|---|---|---|---|
| up to 3 | +12 | +6 | 6 | → |
| over 3 to 6 | +20 | +12 | 8 | → |
| over 6 to 10 | +24 | +15 | 9 | → |
| over 10 to 14 | +29 | +18 | 11 | → |
| over 14 to 18 | +29 | +18 | 11 | → |
| over 18 to 24 | +35 | +22 | 13 | → |
| over 24 to 30 | +35 | +22 | 13 | → |
| over 30 to 40 | +42 | +26 | 16 | → |
| over 40 to 50 | +42 | +26 | 16 | → |
| over 50 to 65 | +51 | +32 | 19 | → |
| over 65 to 80 | +51 | +32 | 19 | → |
| over 80 to 100 | +59 | +37 | 22 | → |
| over 100 to 120 | +59 | +37 | 22 | → |
| over 120 to 140 | +68 | +43 | 25 | → |
| over 140 to 160 | +68 | +43 | 25 | → |
| over 160 to 180 | +68 | +43 | 25 | → |
| over 180 to 200 | +79 | +50 | 29 | → |
| over 200 to 225 | +79 | +50 | 29 | → |
| over 225 to 250 | +79 | +50 | 29 | → |
| over 250 to 280 | +88 | +56 | 32 | → |
| over 280 to 315 | +88 | +56 | 32 | → |
| over 315 to 355 | +98 | +62 | 36 | → |
| over 355 to 400 | +98 | +62 | 36 | → |
| over 400 to 450 | +108 | +68 | 40 | → |
| over 450 to 500 | +108 | +68 | 40 | → |
⊂⊃Common fits that use this class
Partners of p6 in the preferred fits of JIS B 0401 (1998), the Japanese counterpart of ISO 286. Click one to open it in the calculator.
📚Sources
We compared the technical documents below and use values that agree in at least two of them.
- MISUMI jp.misumi-ec.com
- NBK (Nabeya Bi-tech) fujiikougyou.sakura.ne.jpfujiikougyou.sakura.ne.jpfujiikougyou.sakura.ne.jp
- Mitsubishi Materials mitsubishicarbide.netmitsubishicarbide.net
- NSK nsk.com
- Miki Pulley mikipulley.co.jpmikipulley.co.jp
- KHK (Kohara Gear) khkgears.co.jpkhkgears.co.jp